E1SCA18-8.000M TR

E1S Series REGULATORY COMPLIANCE 2011/65 + 2015/863 191 SVHC ITEM DESCRIPTION Quartz Crystal Resonator HC49/UP Short 2 Pad Surface Mount (SMD) 3.2mm Height Metal Resistance Weld Seal ELECTRICAL SPECIFICATIONS Nominal Frequency 3.579545MHz to 50MHz Frequency Tolerance/Stability ±50ppm at 25°C, ±100ppm over 0°C to +70°C ±50ppm at 25°C, ±100ppm over -20°C to +70°C ±50ppm at 25°C, ±100ppm over -40°C to +85°C ±30ppm at 25°C, ±50ppm over 0°C to +70°C ±30ppm at 25°C, ±50ppm over -20°C to +70°C ±30ppm at 25°C, ±50ppm over -40°C to +85°C ±15ppm at 25°C, ±30ppm over 0°C to +70°C ±15ppm at 25°C, ±30ppm over -20°C to +70°C ±15ppm at 25°C, ±30ppm over -40°C to +85°C ±15ppm at 25°C, ±20ppm over 0°C to +70°C ±15ppm at 25°C, ±20ppm over -20°C to +70°C ±15ppm at 25°C, ±20ppm over -40°C to +85°C ±10ppm at 25°C, ±15ppm over 0°C to +70°C ±10ppm at 25°C, ±15ppm over -20°C to +70°C ±10ppm at 25°C, ±15ppm over -40°C to +85°C ±15ppm at 25°C, ±30ppm over -40°C to +105°C ±30ppm at 25°C, ±50ppm over -40°C to +105°C ±50ppm at 25°C, ±100ppm over -40°C to +105°C ±30ppm at 25°C, ±50ppm over -40°C to +125°C ±50ppm at 25°C, ±100ppm over -40°C to +125°C ±30ppm at 25°C, ±50ppm over -55°C to +125°C ±50ppm at 25°C, ±100ppm over -55°C to +125°C Aging at 25°C ±5ppm/year Maximum Load Capacitance Series Resonant, 10pF Parallel Resonant to 50pF Parallel Resonant Shunt Capacitance 7pF Maximum Equivalent Series Resistance See the Equivalent Series Resistance (ESR), Mode of Operation, and Crystal Cut Table Below Mode of Operation AT-Cut Fundamental (Only available over Nominal Frequency range of 3.579545MHz to 30MHz) AT-Cut Third Overtone (Only available over Nominal Frequency range of 24.576MHz to 50MHz) BT-Cut Fundamental (Only available with Frequency Tolerance/Stability of ±50ppm at 25°C, ±100ppm over 0°C to +70°C; Only available over Nominal Frequency range of 24MHz to 40MHz) Drive Level 1mWatt Maximum Storage Temperature Range -55°C to +125°C Insulation Resistance 500 Megaohms Minimum (Measured at 100Vdc) EQUIVALENT SERIES RESISTANCE (ESR), MODE OF OPERATION AND CRYSTAL CUT Frequency Range ESR (Ohms Max) Mode Frequency Range ESR (Ohms Max) Mode 3.579545MHz to 4.999999MHz 200 AT-Cut Fundamental 15MHz to 15.999999MHz 60 AT-Cut Fundamental 5MHz to 5.999999MHz 150 AT-Cut Fundamental 16MHz to 23.999999MHz 50 AT-Cut Fundamental 6MHz to 7.999999MHz 102 AT-Cut Fundamental 24MHz to 30MHz 40 AT-Cut Fundamental 8MHz to 8.999999MHz 90 AT-Cut Fundamental 24.576MHz to 29.999999MHz 150 AT-Cut Third Overtone 9MHz to 9.999999MHz 80 AT-Cut Fundamental 30MHz to 50MHz 100 AT-Cut Third Overtone 10MHz to 14.999999MHz 70 AT-Cut Fundamental 24MHz to 40MHz 40 BT-Cut Fundamental Revised H: 11/09/2015 Page 2 of 10 www.ecliptek.com E1S Series PART NUMBERING GUIDE Revised H: 11/09/2015 Page 3 of 10 www.ecliptek.com E1S Series MECHANICAL DIMENSIONS SUGGESTED SOLDER PAD LAYOUT Revised H: 11/09/2015 Page 4 of 10 www.ecliptek.com E1S Series TAPE & REEL DIMENSIONS Quantity Per Reel: 1,000 units All Dimensions in Millimeters Compliant to EIA-481 Revised H: 11/09/2015 Page 5 of 10 www.ecliptek.com E1S Series RECOMMENDED SOLDER REFLOW METHOD HIGH TEMPERATURE INFRARED/CONVECTION TS MAX to TL (Ramp-up Rate) 3°C/Second Maximum Preheat - Temperature Minimum (TS MIN) - Temperature Typical (TS TYP) - Temperature Maximum(TS MAX) - Time (tS) 150°C 175°C 200°C 60 - 180 Seconds Ramp-up Rate (TL to TP) Time Maintained Above: - Temperature (TL) - Time (tL) 3°C/Second Maximum Peak Temperature (TP) 260°C Maximum for 10 Seconds Maximum Target Peak Temperature(TP Target) 250°C +0/-5°C Time within 5°C of actual peak (tp) 20 - 40 Seconds Ramp-down Rate 6°C/Second Maximum Time 25°C to Peak Temperature (t) 8 Minutes Maximum Moisture Sensitivity Level Level 1 Additional Notes Temperatures shown are applied to body of device. 217°C 60 - 150 Seconds High Temperature Manual Soldering 260°C Maximum for 5 Seconds Maximum, 2 times Maximum. (Temperatures shown are applied to body of device.) Revised H: 11/09/2015 Page 6 of 10 www.ecliptek.com E1S Series RECOMMENDED SOLDER REFLOW METHOD LOW TEMPERATURE INFRARED/CONVECTION TS MAX to TL (Ramp-up Rate) 5°C/Second Maximum Preheat - Temperature Minimum (Ts MIN) - Temperature Typical (Ts TYP) - Temperature Maximum(Ts MAX) - Time (ts) N/A 150°C N/A 30 - 60 Seconds Ramp-up Rate (TL to TP) Time Maintained Above: - Temperature (TL) - Time (tL) 5°C/Second Maximum Peak Temperature (TP) 245°C Maximum Target Peak Temperature (TP Target) 245°C Maximum 2 Times / 230˚C Maximum 1 Time Time within 5°C of actual peak (tp) 10 Seconds Maximum 2 Times / 80 Seconds Maximum 1 Time Ramp-down Rate 5°C/Second Maximum Time 25°C to Peak Temperature (t) N/A Moisture Sensitivity Level Level 1 Additional Notes Temperatures shown are applied to body of device. 150°C 200 Seconds Maximum Low Temperature Manual Soldering 185°C Maximum for 10 Seconds Maximum, 2 times Maximum. (Temperatures shown are applied to body of device.) Revised H: 11/09/2015 Page 7 of 10 www.ecliptek.com